ГЛАВНАЯ             ФОРУМ             БАЗА ДОКУМЕНТОВ             КОНТАКТЫ             ABOUT             RSS ПРОФИЛЬ

    Вспомнить пароль

CWC WoodWorks Design Office v11.1 SR-1 Software
Canadian Wood Council WoodWorks Design Office USA Edition v11.1 SR-1

CWC WoodWorks Design Office v11.1 SR-1


With WoodWorks Sizer, you can size beams, joists, columns and wall studs to meet the 2015 National Design Specification (NDS) for Wood Construction.
  • Specify dead, live, snow and wind loads
  • Automatically pattern loads
  • Generate a materials take-off summary based on your design
  • Design for point, line, area, triangular, and trapezoidal loads simultaneously
  • Automatically check all load combinations as per IBC 2015, ASCE 7-10
  • Analyze the critical load cases for reactions at supports, shear, bending, and deflection
  • Generate detailed analysis reports and diagrams
  • Generate a list of acceptable sections for dimension lumber, heavy timbers, glulam, LVL, or I-joists
  • Use the Materials Database editor to customize the software to your needs
Design Entire Structures – Concept Mode
  • Configure and design a complete structure in plan
  • Do preliminary designs of structures considering gravity loads using the graphical design and analysis work area
  • Perform multi-storey gravity load analysis – sizing all structural members and reporting the reactions at the base
  • Export elements from Concept Mode for further analysis into either Beam Mode or Column Mode
Design Beams – Beam Mode
  • Design individual wood bending members
  • Use Beam Mode to verify the design of critical bending members
  • Generate deflection, shear and bending moment diagrams for any beam or joist in your project
  • Design single or multi-span beams and joists with or without cantilevers
  • Design beams for gravity and uplift loads
  • Specify full, clear or design span
  • Design supporting members for bearing
  • Design Beams with end and interior notches
Design Columns – Column Mode
  • Design individual wood columns, walls, and beam-columns
  • Use Column Mode to verify the design of critical compression members
  • Design columns and wall studs to resist both axial and lateral loads
  • Generate deflection, shear and bending moment diagrams for a single column or wall stud
  • Check wall bottom plate for bearing

With WoodWorks Shearwalls, you can perform complete shearwall design and lateral load analysis.
  • Design shearwalls for multi-storey and irregularly shaped buildings
  • Determine hold-down and drag-strut forces and display them graphically
  • Design shearwalls with or without hold-downs
  • Generate an elevation view to show loads and forces on each shearwall
  • Assign loads to shearlines following a flexible or rigid diaphragm analysis
  • Import Adobe PDF and CAD (.wmf) files to establish the building footprint
  • Model wood structures up to six stories
  • Specify openings in shearwalls such as windows and doors
  • Model roof shapes, including hips, valleys, gables, and overhangs
  • Quickly assess the locations of high aspect ratio segments in a structure
Wind Load Generation
  • Generate wind pressure and resulting lateral loads as per ASCE 7-10
  • Input specific site information, including wind speed up over a hill
  • Manually input lateral loads or modify wind loads that were automatically generated
  • Report shearwall material designs for all wind load cases
  • Check the capacity of wall sheathing and nailing to resist wind suction (components and cladding loads)
  • Check shearwalls for wind serviceability deflection and story drift
Seismic Load Generation
  • Generate seismic loads as per the IBC 2015 (ASCE 7-10)
  • Input site-specific seismic information
  • Manually input lateral loads or modify seismic loads that were automatically generated
  • Report shearwall material designs for all seismic load cases

With WoodWorks Connections, you can design new connections or check the capacity of existing ones.
  • Produce fully dimensioned, CAD-quality drawings
  • Generate a material list for fasteners and steel plates
  • Run designs using lag screws, wood screws, bolts, nails, shear plates or top-mount hangers
Post & Beam Connections
  • Design connectors for beam-to-beam, beam-to-column, and column-to-foundation connections
  • Allows output of beam-to- beam connections as .dxf files for use in AutoCAD
Lapped Shear Connections
  • Design single or double shear connections for wood-to-wood, wood-to-steel, and wood-to-concrete configurations
   Читать статью дальше  (комментариев - 14)


Что ищем:
Расширенный поиск

Adobe, Agnitum, Applied Flow, Aquaveo, Ascon, AspenTech, Autodesk, Bentley, Bricsys, Carlson, CSI, CSoft, Dassault, Delcam, ESRI, Gemcom, GeoStru, Global Mapper, Golden Software, Graitec, Graphisoft, IES, Intergraph, LAVteam, Leica, MicroSurvey, nanoSoft, Nemetschek, PTC, Rarlab, Schlumberger, Siemens, Springer, Tekla, Transoft, Trimble, VariCAD, Wiley, x-Force, ZwSoft

Показать все теги

«    Март 2019    »



If you enjoy our work,
please support us.


yandex money


LAVteam: 1999-2020